20x48 ft hay tarp: width, length and finished coverage
This 20 ft wide reference is 5 ft wider and 6 ft shorter than 15×54. Check cross-stack coverage and end coverage as separate requirements.
- Published flat width
- 20 ft
- Published flat length
- 48 ft
- Finished coverage
- Confirm per vendor and stack
What does the 20 × 48 ft label measure?
Conceptual illustration. You can pause the movement.
Static view: reduced motion is enabled.01 / Published rectangle
Check the vendor's size basis below. A format label does not establish finished coverage.
02 / Finished outside edges
Agree the finished outside dimensions and tolerances. The usable sheet includes its hems; it is not measured between the inner hem lines.
Tarp Supply publishes a cut size; TarpsPlus describes a smaller finished size. The vendor details below identify which applies to this comparison. Ask for finished outside W × L, including hems, with tolerances and named measurement endpoints.
Will this reference cover your measured stack?
Conceptual illustration. You can pause the movement.
Static view: reduced motion is enabled.Measure the surface, not just the footprint
The cover follows a longer route over the pile. Measure over the actual stack to the intended cover edges.
For the 20 × 48 ft reference: compare the measured surface span with the confirmed finished width W. The published 20 ft width does not prove that this illustrated profile fits.
Record the bale dimensions, row arrangement, stack length and intended coverage at both ends.
Send the measured span with a labeled profile. It gives the supplier a fit question to answer.
Start with the real stack length, then specify where the cover must end on each face. Compare that requirement with L finished, not just the nominal 48 ft label. The calculator's stated end allowance is a vendor rule to review for the chosen system.
Use as a starting reference when: confirmed finished width and length cover your measured surface route and chosen end treatment.
Choose another size or system when: either finished dimension is short, or the edge construction does not suit the supplier's proposed covering system.
Common buying error: treating 20 ft as the ground width of a compatible stack. Bale shape, arrangement, settlement and intended cover edges change the fabric route.
First personal reply within 2 business days, with clarifying questions or next steps.
What differs between the two published offers?
| Compare | Tarp Supply | TarpsPlus |
|---|---|---|
| Thickness / fabric weight per area | 12 mil / 7 to 8 oz/yd² | 16 mil / 8 oz/yd² |
| Material and face | High-density polyethylene; heat-sealed seams. | Coated woven polyethylene, silver/black. |
| Hem and reinforcement | Rope-reinforced hem, webbing through the hem and reinforced corners; pipe-insert loops on two sides. Handles available on request. | Rope encased in the hem; reinforced triangular corners; nylon hand grips on the two longest sides and at the corners. |
| Fixings and layout | The listing states eyelets every three feet and brass grommets approximately every 24 inches. Their respective scope is unclear: request a position drawing instead of assuming one pitch or count. | Aluminum grommets approximately every 18 inches. Confirm total count, corner treatment and exact positions on the finished cover. |
| Cut or finished size? | Published as cut size. The vendor describes finished size as about six inches or 3 to 5% shorter after folding and hemming. Confirm actual finished outside width and length; do not subtract a universal allowance. | The vendor describes finished size as approximately six inches or up to 3% smaller. Confirm the finished outside dimensions for the ordered variant. |
| Offer contents | Cover with its listed edge construction. No complete pipe-and-tension kit established in this offer. | Cover and its listed edge features; no complete pipe-and-tension package established here. |
| Primary listing / source | View this 20×48 listing N2 · Tarp Supply hay listings, construction checked 2026-10-27 | View this 20×48 listing N2 · TarpsPlus hay listings, construction checked 2026-10-27 |
Thickness, oz/yd² and grommet pitch describe different properties. They do not establish tear resistance, edge pull-out strength or service life. No comparable finished-cover test results are established by this review. Request a defined test method, specimen, sampling and acceptance criteria for any performance requirement.
Historical US retail price references
| Vendor | Recorded price | Reference |
|---|---|---|
| Tarp Supply | 460.89 USD | Current listing for 20×48 Read 2026-08-20 |
| TarpsPlus | 369.02 USD | Current listing for 20×48 Read 2026-08-20 |
Retail references are not delivered sourcing quotes. Compare the same finished dimensions, construction, included parts, quantity, freight and duty. Historical promotional wording is excluded from the comparison; live prices may differ.
Which nearby reference changes the right dimension?
| Published size | Width versus this reference | Length versus this reference |
|---|---|---|
| 28x48 ft | 8 ft more | unchanged |
| 15x54 ft | 5 ft less | 6 ft more |
| 25x54 ft | 5 ft more | 6 ft more |
Differences are arithmetic on published dimensions, not additional finished coverage or a guarantee of fit.
Send a stack description that can be checked
- Keep 20x48 ft as a starting reference. Add bale dimensions and shape, row arrangement, stack length, the measured surface span and intended cover edges at the sides and ends.
- Request finished outside W × L, tolerances, face orientation and an edge drawing showing hems, reinforcements, fixings and any sleeves. Agree total counts and positions rather than calculating them from a nominal spacing.
- Specify coated-fabric weight per area separately from thickness. Agree the measurement method and sampling; complete-piece weight cannot isolate fabric weight.
- List cover-only versus supplied components, quantities, replacement parts and instructions. Agree checks for seams, hems and the edge assembly, with the test specimen and acceptance criteria stated.
- On receipt, compare outside dimensions, component count, positions and construction with that approved drawing. Record the batch and any deviation before acceptance.
The calculator keeps this format as a reference while asking for the actual stack. Its round-bale model does not infer your bale diameter or arrangement from the cover size.
First personal reply within 2 business days, with clarifying questions or next steps.
For the edge details and water path, see hay tarp failure checks and the hay covering value guide. Review the family reception checks with the supplier.