25x54 ft hay tarp: width, length and finished coverage
This 25 ft wide, 54 ft long reference appears as both a cover listing and a pre-assembled system. Compare the finished size and supplied components before comparing prices.
- Published flat width
- 25 ft
- Published flat length
- 54 ft
- Finished coverage
- Confirm per vendor and stack
What does the 25 × 54 ft label measure?
Conceptual illustration. You can pause the movement.
Static view: reduced motion is enabled.01 / Published rectangle
Check the vendor's size basis below. A format label does not establish finished coverage.
02 / Finished outside edges
Agree the finished outside dimensions and tolerances. The usable sheet includes its hems; it is not measured between the inner hem lines.
Tarp Supply publishes a cut size; the reviewed A1 listing does not establish the cut/finished basis. The vendor details below identify which applies to this comparison. Ask for finished outside W × L, including hems, with tolerances and named measurement endpoints.
Will this reference cover your measured stack?
Conceptual illustration. You can pause the movement.
Static view: reduced motion is enabled.Measure the surface, not just the footprint
The cover follows a longer route over the pile. Measure over the actual stack to the intended cover edges.
For the 25 × 54 ft reference: compare the measured surface span with the confirmed finished width W. The published 25 ft width does not prove that this illustrated profile fits.
Record the bale dimensions, row arrangement, stack length and intended coverage at both ends.
Send the measured span with a labeled profile. It gives the supplier a fit question to answer.
Start with the real stack length, then specify where the cover must end on each face. Compare that requirement with L finished, not just the nominal 54 ft label. The calculator's stated end allowance is a vendor rule to review for the chosen system.
Use as a starting reference when: confirmed finished width and length cover your measured surface route and chosen end treatment.
Choose another size or system when: either finished dimension is short, or the edge construction does not suit the supplier's proposed covering system.
Common buying error: treating 25 ft as the ground width of a compatible stack. Bale shape, arrangement, settlement and intended cover edges change the fabric route.
First personal reply within 2 business days, with clarifying questions or next steps.
What differs between the two published offers?
| Compare | Tarp Supply | A1 Tarps, Performer |
|---|---|---|
| Thickness / fabric weight per area | 12 mil / 7 to 8 oz/yd² | 17 mil / 7.30 oz/yd² |
| Material and face | High-density polyethylene; heat-sealed seams. | White/black coated woven polyethylene. |
| Hem and reinforcement | Rope-reinforced hem, webbing through the hem and reinforced corners; pipe-insert loops on two sides. Handles available on request. | Sleeved PVC pipe sections along the length; obtain the layout for this exact size. |
| Fixings and layout | The listing states eyelets every three feet and brass grommets approximately every 24 inches. Their respective scope is unclear: request a position drawing instead of assuming one pitch or count. | UV-stable poly rope and the vendor's Super Cinch tension device. Component names do not establish positions, forces or an installation method. |
| Cut or finished size? | Published as cut size. The vendor describes finished size as about six inches or 3 to 5% shorter after folding and hemming. Confirm actual finished outside width and length; do not subtract a universal allowance. | Cut versus finished basis not established in the reviewed listing. Request finished outside dimensions; another vendor's size reduction does not apply. |
| Offer contents | Cover with its listed edge construction. No complete pipe-and-tension kit established in this offer. | Pre-assembled cover with sleeved PVC pipe sections, rope and a tension device. Confirm quantities, supplied parts and instructions. |
| Primary listing / source | View this 25×54 listing N2 · Tarp Supply hay listings, construction checked 2026-10-27 | View this 25×54 listing N2 · A1 Performer PR25X5417MILWB, construction checked 2026-10-27 |
Thickness, oz/yd² and grommet pitch describe different properties. They do not establish tear resistance, edge pull-out strength or service life. No comparable finished-cover test results are established by this review. Request a defined test method, specimen, sampling and acceptance criteria for any performance requirement.
Conceptual illustration. You can pause the movement.
Static view: reduced motion is enabled.Same nominal 25 x 54 ft, different offer contents
Historical listings read 2026-08-20. The drawings identify components, not relative quality or an installation method.
Cover listing
Tarp Supply
12 mil · 7 to 8 oz/yd²
648.19 USD
Cover with its listed edge construction. No complete pipe-and-tension kit established in this offer.
Complete-system listing
Read the drawing: blue edges = sleeves; gray bars = PVC pipe sections; orange curve = rope; orange box = tension device. Shapes and positions are symbolic.
A1 Tarps, Performer
17 mil · 7.30 oz/yd²
654.00 USD
Pre-assembled cover with sleeved PVC pipe sections, rope and a tension device. Confirm quantities, supplied parts and instructions.
The accessory drawings are symbolic. Obtain the actual component list and the vendor's instructions; no pipe dimensions, forces or installation pattern are inferred here.
Historical US retail price references
| Vendor | Recorded price | Reference |
|---|---|---|
| Tarp Supply | 648.19 USD | Current listing for 25×54 Read 2026-08-20 |
| A1 Tarps, Performer | 654.00 USD | Current listing for 25×54 Read 2026-08-20 |
Retail references are not delivered sourcing quotes. Compare the same finished dimensions, construction, included parts, quantity, freight and duty. Historical promotional wording is excluded from the comparison; live prices may differ.
Which nearby reference changes the right dimension?
| Published size | Width versus this reference | Length versus this reference |
|---|---|---|
| 28x48 ft | 3 ft more | 6 ft less |
| 15x54 ft | 10 ft less | unchanged |
| 20x48 ft | 5 ft less | 6 ft less |
Differences are arithmetic on published dimensions, not additional finished coverage or a guarantee of fit.
Send a stack description that can be checked
- Keep 25x54 ft as a starting reference. Add bale dimensions and shape, row arrangement, stack length, the measured surface span and intended cover edges at the sides and ends.
- Request finished outside W × L, tolerances, face orientation and an edge drawing showing hems, reinforcements, fixings and any sleeves. Agree total counts and positions rather than calculating them from a nominal spacing.
- Specify coated-fabric weight per area separately from thickness. Agree the measurement method and sampling; complete-piece weight cannot isolate fabric weight.
- List cover-only versus supplied components, quantities, replacement parts and instructions. Agree checks for seams, hems and the edge assembly, with the test specimen and acceptance criteria stated.
- On receipt, compare outside dimensions, component count, positions and construction with that approved drawing. Record the batch and any deviation before acceptance.
The calculator keeps this format as a reference while asking for the actual stack. Its round-bale model does not infer your bale diameter or arrangement from the cover size.
First personal reply within 2 business days, with clarifying questions or next steps.
For the edge details and water path, see hay tarp failure checks and the hay covering value guide. Review the family reception checks with the supplier.