Qualitora LLC, US sourcing partner NM Business ID 7688237 First personal reply within 2 business days

28x48 ft hay tarp: width, length and finished coverage

This 48 ft long reference adds 8 ft of published width over 20×48. That width runs over the pile, so measure the surface rather than just its ground footprint.

Published market reference. We hold no stock. Prices below are historical retail records read 2026-08-20; construction details were checked 2026-10-27. These are reference offers, not our products or quotes.
Published flat width
28 ft
Published flat length
48 ft
Finished coverage
Confirm per vendor and stack

What does the 28 × 48 ft label measure?

Conceptual illustration. You can pause the movement.

Static view: reduced motion is enabled.

01 / Published rectangle

28 × 48 ft published size 28 ft width 48 ft length

Check the vendor's size basis below. A format label does not establish finished coverage.

02 / Finished outside edges

Measure finished W and L including hems W finished L finished

Agree the finished outside dimensions and tolerances. The usable sheet includes its hems; it is not measured between the inner hem lines.

The first rectangle uses this format's published proportions. The second is symbolic and not to the same scale. Highlights identify width, length and finished edges; no universal hemming deduction is shown.

Tarp Supply publishes a cut size; TarpsPlus describes a smaller finished size. The vendor details below identify which applies to this comparison. Ask for finished outside W × L, including hems, with tolerances and named measurement endpoints.

Will this reference cover your measured stack?

Conceptual illustration. You can pause the movement.

Static view: reduced motion is enabled.
Surface span and ground footprint are different measurements Surface span Ground footprint

Measure the surface, not just the footprint

The cover follows a longer route over the pile. Measure over the actual stack to the intended cover edges.

For the 28 × 48 ft reference: compare the measured surface span with the confirmed finished width W. The published 28 ft width does not prove that this illustrated profile fits.

Record the bale dimensions, row arrangement, stack length and intended coverage at both ends.

Send the measured span with a labeled profile. It gives the supplier a fit question to answer.

Stack length plus the chosen end coverage Measured stack length L finished: confirm both ends

Start with the real stack length, then specify where the cover must end on each face. Compare that requirement with L finished, not just the nominal 48 ft label. The calculator's stated end allowance is a vendor rule to review for the chosen system.

End view of a conceptual profile, not a sizing or stacking recommendation. The moving highlight follows the measurement route; it does not add an allowance or specify a cover size.

Use as a starting reference when: confirmed finished width and length cover your measured surface route and chosen end treatment.

Choose another size or system when: either finished dimension is short, or the edge construction does not suit the supplier's proposed covering system.

Common buying error: treating 28 ft as the ground width of a compatible stack. Bale shape, arrangement, settlement and intended cover edges change the fabric route.

First personal reply within 2 business days, with clarifying questions or next steps.

What differs between the two published offers?

Vendor-stated construction, checked 2026-10-27; confirm the current ordered variant
CompareTarp SupplyTarpsPlus
Thickness / fabric weight per area12 mil / 7 to 8 oz/yd²16 mil / 8 oz/yd²
Material and faceHigh-density polyethylene; heat-sealed seams.Coated woven polyethylene, silver/black.
Hem and reinforcementRope-reinforced hem, webbing through the hem and reinforced corners; pipe-insert loops on two sides. Handles available on request.Rope encased in the hem; reinforced triangular corners; nylon hand grips on the two longest sides and at the corners.
Fixings and layoutThe listing states eyelets every three feet and brass grommets approximately every 24 inches. Their respective scope is unclear: request a position drawing instead of assuming one pitch or count.Aluminum grommets approximately every 18 inches. Confirm total count, corner treatment and exact positions on the finished cover.
Cut or finished size?Published as cut size. The vendor describes finished size as about six inches or 3 to 5% shorter after folding and hemming. Confirm actual finished outside width and length; do not subtract a universal allowance.The vendor describes finished size as approximately six inches or up to 3% smaller. Confirm the finished outside dimensions for the ordered variant.
Offer contentsCover with its listed edge construction. No complete pipe-and-tension kit established in this offer.Cover and its listed edge features; no complete pipe-and-tension package established here.
Primary listing / sourceView this 28×48 listing
N2 · Tarp Supply hay listings, construction checked 2026-10-27
View this 28×48 listing
N2 · TarpsPlus hay listings, construction checked 2026-10-27

Thickness, oz/yd² and grommet pitch describe different properties. They do not establish tear resistance, edge pull-out strength or service life. No comparable finished-cover test results are established by this review. Request a defined test method, specimen, sampling and acceptance criteria for any performance requirement.

Historical US retail price references

Read 2026-08-20; the current links are not price archives
VendorRecorded priceReference
Tarp Supply645.19 USDCurrent listing for 28×48
Read 2026-08-20
TarpsPlus516.63 USDCurrent listing for 28×48
Read 2026-08-20

Retail references are not delivered sourcing quotes. Compare the same finished dimensions, construction, included parts, quantity, freight and duty. Historical promotional wording is excluded from the comparison; live prices may differ.

Which nearby reference changes the right dimension?

Published sizeWidth versus this referenceLength versus this reference
33x48 ft5 ft moreunchanged
20x48 ft8 ft lessunchanged
25x54 ft3 ft less6 ft more

Differences are arithmetic on published dimensions, not additional finished coverage or a guarantee of fit.

Send a stack description that can be checked

  1. Keep 28x48 ft as a starting reference. Add bale dimensions and shape, row arrangement, stack length, the measured surface span and intended cover edges at the sides and ends.
  2. Request finished outside W × L, tolerances, face orientation and an edge drawing showing hems, reinforcements, fixings and any sleeves. Agree total counts and positions rather than calculating them from a nominal spacing.
  3. Specify coated-fabric weight per area separately from thickness. Agree the measurement method and sampling; complete-piece weight cannot isolate fabric weight.
  4. List cover-only versus supplied components, quantities, replacement parts and instructions. Agree checks for seams, hems and the edge assembly, with the test specimen and acceptance criteria stated.
  5. On receipt, compare outside dimensions, component count, positions and construction with that approved drawing. Record the batch and any deviation before acceptance.

The calculator keeps this format as a reference while asking for the actual stack. Its round-bale model does not infer your bale diameter or arrangement from the cover size.

First personal reply within 2 business days, with clarifying questions or next steps.

For the edge details and water path, see hay tarp failure checks and the hay covering value guide. Review the family reception checks with the supplier.